Penetrates 2-3 mm into the concrete surface and cross-links densely, curing porcelain-like at the surface. Unlike film-forming waterproofing it does not peel — so peeling that leads to leaking never happens.
Penetrates 2-3 mm into the substrateSurface cures into a porcelain waterproof layer4H hardness, extreme abrasion resistanceIncludes a 20 ml trial kit (random colour)
Penetrating versus surface film: different mechanism, different result
A low-viscosity two-component system penetrates the capillaries of the concrete and cross-links and cures porcelain-like within the top 2-3 mm. The waterproof layer is part of the substrate itself, so delamination between layers is not a failure mode.
Pack Size4.2 kg total (ratio A:B = 3:4)
Pencil Hardness4H
Key figures
Marken: verifiable key figures
4HPencil Hardness
3000 h, no abnormalityWater Resistance
6.0 MPaAdhesion Strength
2-3 mmPenetration Depth
Every figure traces back to a third-party test report
Where Waterproof Series is used
Concrete element reinforcement · Anti-seepage sealing for terrazzo / stone / ceramic and similar high-traffic areas, where film durability and cleaning tolerance matter most.
Penetrates 2-3 mm into the substrate
Surface cures into a porcelain waterproof layer
4H hardness, extreme abrasion resistance
3000 h water resistance
4000 h ageing resistance
Technical specifications
Full specification
Adhesion Strength6.0 MPa
Pencil Hardness4H
Abrasion Resistance0.015 g
Water Contact Angle105°
Heat Resistance250 °C
Water Resistance3000 h, no abnormality
Weathering Resistance4000 h, no blistering or peeling
Penetration Depth2-3 mm
Theoretical Coverage1 kg ≈ 10-14 m² per coat
Shelf Life24 months
Pack Size4.2 kg total (ratio A:B = 3:4)
Pack4.2 kg total (ratio A:B = 3:4)
Colour systemhonma HC colour system (1,500 colours; 939 named codes published on this site)
Marken · application reference
Applications
Where to use it, where not to
Suitable for
Concrete element reinforcement
Anti-seepage sealing for terrazzo / stone / ceramic
Concrete colour-corrective coating
Bathroom / basement waterproofing
Garage floor protection
Swimming pool (as part of a system)
Not suitable for
Through-cracks without structural repair
Areas with ongoing leakage where the pressure source has not been eliminated
Application
Substrate → mixing → coating → curing
Substrate requirements
Moisture content
< 10%
pH value
< 10
Strength
Sound, no hollow areas
Application steps
Mix parts A and B in the stated ratio and stir until uniform with no colour streaks
Apply two coats by brush or roller; recoat after the first is touch-dry
Cure to specification; avoid direct sun and strong wind that dry the film too fast
The water-ponding test may only be carried out after curing is complete
5–35 °CTemperature
<80%Humidity
Touch-dry 2 h (25 °C) / hard-dry 12 hTouch dry
Full cure 7 days (25 °C)Full cure
How it differs
Different from conventional coating systems
Film formation
Water evaporation, particle coalescence
A/B cross-linking cure
Film structure
Thermoplastic, softens with heat
Cross-linked, dense, porcelain-like
Pencil Hardness
Typical product level
4H◊
◊ From third-party test reports
How to use the trial kit
1The full pack arrives together with a 20 ml trial kit
2Try the trial kit first for feel and application
3Confirm with our team
4Open the full pack and start the project
Once the full pack is opened, cross-border orders cannot be returned or exchanged
